How to connect a JoJo tank to your house: diagram and steps

Updated 19 November 2026 · Independent guide by Home Water Backup

To connect a JoJo tank to your house, the municipal supply is split after the water meter: one branch fills the tank through a float valve, and the tank feeds a pump that pushes water into the house pipes. Non-return valves stop tank water flowing back into the municipal main. The diagram below shows the usual layout. The connection to your household plumbing must be made by a qualified plumber.

How a backup water tank connects to a houseMunicipal water splits at a tee. One branch fills the tank through a float valve. The tank feeds a pump, which pushes water through a non-return valve to the house. The other branch is a bypass that feeds the house directly through its own non-return valve.Municipal supplyafter the water meterTankon a level baseFloat valveOverflowIsolating valveIsolatingvalveNon-returnvalveNon-return valvePump+ pressure controlHousetaps, toilets, geyserBypass line
Typical layout for a municipal-fed backup tank with a booster pump and a bypass. Your plumber may arrange it differently to suit your property and your municipality's bylaws.

What each part does

Part Job
Isolating valve before the tank Shuts off the feed to the tank for maintenance. JoJo’s guide calls for a ball valve between the municipal feed and the float valve.
Float valve Sits inside the tank at the inlet. It closes when the tank is full and opens when the level drops.
Overflow Carries water away safely if the float valve fails. Pipe it to a drain or the garden, not against the house wall.
Tank outlet and isolating valve Lets water out to the pump. A valve here lets you remove the pump without draining the tank.
Pump and pressure controller The controller senses the pressure drop when a tap opens and starts the pump.
Non-return valve after the pump Stops municipal water pushing backwards through the pump.
Bypass line with non-return valve Lets municipal water reach the house directly when the supply is on, and stops pumped water escaping into the street main when it is off.

The steps a plumber follows

  1. Place the tank on its finished base, close to where the supply enters the house. See how to install a JoJo water tank.
  2. Shut off the water at the meter and cut into the supply pipe after the meter.
  3. Fit a tee. One branch goes to the tank inlet with an isolating valve and the float valve. The other continues to the house as the bypass, with a non-return valve.
  4. Fit the overflow and pipe it to a suitable place.
  5. Connect the tank outlet to the pump. JoJo specifies at least 25 mm pipe here, with an isolating valve.
  6. Connect the pump to the house line after the bypass non-return valve, through its own non-return valve. JoJo specifies at least 20 mm pipe.
  7. Fit backflow protection of the type your municipality requires.
  8. Fill and test. Check every joint for leaks, check that the float valve shuts off, and test the pump with the municipal supply turned off.

Rules that affect the connection

Tank water must never flow back into the municipal main

This is the rule every municipality enforces, because backflow from one house can contaminate the water for a whole street. It is why the connection is a job for a registered plumber, and why the type of backflow device matters.

  • Durban (eThekwini). The 2023 Water By-law requires written approval for installation work and a registered plumber. It accepts water discharging into the storage tank through an air gap, or an approved backflow preventer. It also requires that pumped water is drawn from a storage tank, not directly from the main.
  • Cape Town. Approval is needed before an alternative water system is plumbed in. The City’s guidelines state that “non-return valves and standard stopcock valves are not approved back-flow prevention devices” for these systems, and that an RPZ backflow preventer, or an air gap tank, is required.
  • Johannesburg. The 2004 Water Services By-laws allow only a qualified plumber to do installation work beyond repairing or replacing an existing pipe or fitting, and list an air gap into a storage tank or an approved backflow preventer as accepted measures.
  • Pretoria (Tshwane). The 2014 Water Supply By-laws restrict installation work to a plumber or someone working under a plumber’s control.

By-laws change. Ask your plumber to confirm the current requirement for your municipality.

Keep rainwater separate

If your tank collects rainwater, do not connect it to pipes that carry municipal drinking water. Cape Town does not allow any interconnection between the two, and Johannesburg’s and Tshwane’s by-laws only exempt rainwater tanks that are not connected to the water installation. Use rainwater through its own taps for the garden, cleaning and, with the right plumbing, toilets.

Check the pressure at your property

JoJo’s float valve kit is “not suited for pressure higher than 4 Bar”. If your municipal pressure is high, ask the plumber whether a pressure-reducing valve is needed before the tank.

Common questions

Can I connect a JoJo tank to my house myself?

In most cities, no. The water by-laws of eThekwini, Johannesburg, Cape Town and Tshwane restrict work on a water installation to registered or qualified plumbers. JoJo also advises using a plumber or professional installer because the system ties into the building's main water supply.

Why do I need a non-return valve?

To stop water flowing the wrong way. JoJo's guide calls for non-return valves between the pump and the mains and between the house and the mains, so that pumped tank water cannot be pushed back into the municipal supply.

Is a non-return valve enough for the municipality?

Not everywhere. Cape Town's guidelines say non-return valves are not approved backflow prevention for alternative water systems and require a reduced pressure zone (RPZ) backflow preventer or an air gap. eThekwini's by-law accepts an air gap into the tank or an approved backflow preventer.

What pipe size do I need?

JoJo's installation guide specifies pipe of at least 25 mm diameter from the tank to the pump, and at least 20 mm from the pump to where it joins the house supply. The standard outlet on a JoJo water tank is 40 mm, so reducers are needed.

Sources

  1. JoJo, Water storage solutions installation guide (December 2025)
  2. JoJo, Using our water tank float valve kit (January 2024)
  3. Open By-laws (Laws.Africa), eThekwini Municipality Water By-law, 2023
  4. City of Cape Town, Guidelines for the installation of alternative water systems
  5. Open By-laws (Laws.Africa), City of Johannesburg Water Services By-laws, 2004
  6. Open Gazettes South Africa, City of Tshwane Water Supply By-laws (Provincial Gazette 203, 23 July 2014)