How to install a JoJo water tank
To install a JoJo water tank you choose a spot close to your water supply, build a level base slightly wider than the tank, place the empty tank on it, fit the inlet, overflow and outlet, and then have a plumber connect it to the house. The base is the part people get wrong, and a poor base can crack the tank and void the warranty. Here is each step.
1. Choose the position
- Close to the supply. Near where the municipal pipe enters the house keeps pipe runs short and costs down.
- Firm ground. Not on fill, not beside a retaining wall that was not built for the load.
- Room to work. Leave space to reach the fittings and the pump.
- Under a gutter, if you want to collect rainwater.
- Check the rules. Estates and sectional title schemes often have their own rules. In Cape Town, a tank over 10 000 litres, or on a structure more than 1 metre above ground, needs building plan approval.
2. Build the base
Water weighs one kilogram per litre. A full 5 250 litre tank puts more than five tonnes on its base.
JoJo’s installation guide says tanks “must be installed on a sound, level and smooth surface”, which can be level paving, a properly designed tank stand or a concrete slab, “ideally with a concrete surface bed at least 85mm thick”. The base must be “free of any protrusions and at least 100mm wider than the base of the tank”. JoJo’s FAQ adds that no tank may be placed on bare ground.
JoJo’s recommended base sizes:
| Tank | Tank diameter | Minimum base |
|---|---|---|
| 750 L slimline | 760 mm | 860 mm |
| 2 400 L and 2 700 L | 1 420 mm | 1 520 mm |
| 5 250 L | 1 820 mm | 1 920 mm |
| 10 000 L | 2 200 mm | 2 300 mm |
Other makers say much the same. Eco Tanks, for example, calls a level, solid concrete platform that supports the entire base of the tank “the best possible tank stand”. Always follow the instructions for the brand you bought, because the warranty depends on it.
Let new concrete cure before loading it. JoJo’s stand guide advises at least 14 days.
3. Using a tank stand
A stand raises the tank for gravity pressure or to clear a slope. JoJo’s rules for stands:
- the tank “must not overhang the stand at all”
- beams should be no more than 50 mm apart
- no iron or steel fittings on the tank connections
A raised full tank is a heavy load high up. Have a tall stand designed and built by someone qualified.
4. Place the tank
- Sweep the base. A single stone under a full tank can damage it.
- Move the tank empty. Roll it on its side or carry it; do not drag it over rough ground.
- Stand it centred on the base with the outlet facing where the pump will go.
5. Fit the connections
Use the moulded fittings the tank comes with. JoJo warns that drilling extra holes or altering the tank ends the warranty.
- Inlet with float valve, near the top, for the municipal feed.
- Overflow. JoJo’s guide says to add an elbow and pipe and route it to a suitable area so that water is not wasted.
- Outlet, at the bottom. The standard outlet on a JoJo water tank is 40 mm.
- Lid. Clip it on firmly and keep it on.
6. Connect to the house
This is plumber’s work. Municipal by-laws restrict connections to the water installation to qualified or registered plumbers, and require protection against backflow. Our guide on how to connect a JoJo tank to your house has a diagram and the rules for each major city.
7. Fill and check
- Fill the tank slowly the first time and watch the base for any movement.
- Check every fitting for drips.
- Check that the float valve shuts off just below the overflow.
- Run the pump with the municipal supply turned off to confirm the house is fed from the tank.
What you can do yourself, and what you cannot
| You can usually do | Leave to a professional |
|---|---|
| Clear and level the site | Connecting to the municipal supply or house pipes |
| Lay paving or cast a small slab, to the maker’s specification | Backflow protection and any municipal certificate |
| Place a rainwater tank fed only by gutters | The electrical point for the pump |
| Routine checks and cleaning | A tall tank stand |
For what a professional installation costs, see installation prices.
Common questions
Can a JoJo tank stand on paving or bare ground?
Not on bare ground. JoJo's FAQ says no tank may be placed on bare ground. Its installation guide accepts level paving, a properly designed tank stand, or a concrete slab, ideally at least 85 mm thick.
How big must the base be?
JoJo specifies a base at least 100 mm wider than the base of the tank. For a 2 700 litre tank (1 420 mm diameter) it recommends a 1 520 mm base, and for a 5 250 litre tank (1 820 mm) a 1 920 mm base.
Can I drill extra holes in the tank?
No. JoJo's warranty wording says that if you drill additional holes or make any alterations to the tank, the warranty falls away. Use the fittings the tank comes with.
How long must a new concrete slab cure before the tank goes on?
JoJo's tank stand guide advises leaving cement to cure for at least 14 days before placing the tank. Follow your builder's advice for your slab.